Xinxiang jinrui machinery factory
High quality products are the golden key to open the market door
Add to Cart
U Trough screw conveyor is made up of screw part, bearing part and driving devices. Screw part is supported by both ends of bearing and middle bearing and driven by driving devices. When the screw conveyor operate, handling material will come into the feed chute by inlet, then do axial movement along the chute under the action of rotate screw until out of the outlet.
U Trough screw conveyor is bulk material handling equipment, it provides enclosed transfer while moving materials horizontally or at an angle,it can deliver materials from one or more inlet points to one or more discharge points. Screw conveyors can be operated with the flow of material inclined upward. When space allows, this is a very economical method of elevating and conveying. As the angle of inclination increases, the capacity of a given unit rapidly decreases.
1. The structure is relatively simple and the cost is low;
2. Reliable work, simple maintenance and management;
3. The size is compact, the section size is small, the occupation area is small;
4. Easy to load and uninstall. The horizontal screw conveyor can be loaded and unloaded at any point on its transmission line;
5. The unit energy consumption is large;
U Trough screw conveyor is widely used in building materials, metallurgy, chemical industry, machinery, light industry, grain and food industry. U-type screw conveyor is suitable for conveying powder Shaped, granular, small bulk materials, such as cement, fly ash, grain, chemical fertilizer, mineral powder, sand, soda and so on. U-shaped screw conveyor is not suitable for transporting materials that are easy to deteriorate, sticky and easy to caking. The working environment temperature of the conveyor is usually-20 °40 °, the temperature of the conveying material is generally 20 °80 °℃, the U-shaped screw conveyor is suitable for horizontal and small inclination arrangement, and the inclination angle is not more than 15 degrees. If the tilt angle is too large, the tubular screw conveyor should be selected.
| Model | Diameter mm | Pitch mm | Speed r/min | Standard Capacity(m3/h) | Speed r/min | Standard Capacity(m3/h) | Speed r/min | Standard Capacity(m3/h) | ||||||
| φ0.45 | φ0.33 | φ0.15 | φ0.45 | φ0.33 | φ0.15 | φ0.45 | φ0.33 | φ0.15 | ||||||
| LS200 | 200 | 200 | 100 | 16.9 | 12.4 | 5.6 | 80 | 13.5 | 9.9 | 4.5 | 63 | 10.7 | 7.8 | 3.6 |
| LS315 | 315 | 315 | 80 | 52.9 | 38.8 | 17.6 | 63 | 41.6 | 30.5 | 13.9 | 50 | 33.1 | 24.2 | 11 |
| LS400 | 400 | 355 | 71 | 85.3 | 62.5 | 28.4 | 56 | 67.3 | 49.3 | 22.4 | 45 | 54.1 | 39.6 | 18 |
| LS500 | 500 | 400 | 63 | 133.2 | 97.7 | 44.4 | 50 | 105.8 | 77.6 | 35.3 | 40 | 84.6 | 62.0 | 28.2 |
| LS630 | 630 | 450 | 50 | 188.9 | 138.5 | 63.0 | 40 | 151.1 | 110.8 | 50.4 | 32 | 120.9 | 88.6 | 40.3 |
| Material to be processed: _____ | Working environment is indoor or outdoor:________ |
| Handling capacity: ________per hour | Working environment temperature: _______ ℃ |
| Bulk Density: _____t/m3 | Installation form is horizontal or inclined : ________ |
| Conveying distance: ________ | If it is inclined,what is the inclined degree_____° |
| Material size:____mm | Water content:____% |
| Material temperature: _______ ℃ | Working power supply: _____V ______HZ ______PH |
